- Igt Slots For Pc
- Igt Slot Machine Troubleshooting
- Igt Slot Machines For Sale
- Igt Slot Machines How To Clear Codes Without
- Igt Slot Machines Programming Codes
- Igt Slot Machine Repair
Typically most problems with an IGT S+ slot machine are not cured with the use of a RAM clear chip, so only do the following procedure if you're sure you really need to do a full clear. Turn the machine's power off. Remove the coin tray and hopper. Locate the round knob on the silver MPU board tray that is behind the hopper. ¾All soft meters reset to “0” ¾Power up with just the clear chips in ¾Message CH P and CL P will appear, and then all lights flashing. Clearing Procedure (using Mikohn SAS) 1. Power machine off and remove MPU 2.remove EPROMS U28 and U43 3. Install clear chip U28 and U43 in there correct lo-cations 4. Turn power on (depending on what.
- You will note that most of the machines will say Max Hopper Pay 400 or 1000 on the reel glass, this is the same thing but smaller. Note it is not possible to make any of these settings changes until you have 0 credits on the machine. Is it possible to clear a 3300 code on an IGT w/o filling the hopper? Post a Reply to This Message.
- Press self test switch for 3 seconds If error will not clear replace EPROM Also if the processor could not read or write to the named chip Press test button for 3 seconds Error code clears from display. Most of the errors can be resolved with little help but many need technical knowledge.
- Gamekingslots.com sells IGT Slot Machines,Bally Slot Machines,WMS Slot Machines,Slot Machines Parts and Accessories,Aristocrat Slot Machines, slot machines for sale JavaScript seems to be disabled in your browser.
INITIAL SLOT MACHNE SETUP INSTRUCTIONS
Before you can setup your machine, you have to get it out of it’s shipping crate. There are many staples holding the crate together. Remove the top using a hammer and a screwdriver or a pry bar. Then remove one side panel the same way. With a side panel and the top gone the machine will come out of the crate.
Igt Slots For Pc
Now you can begin to set up the machine.
If a stand is going to be used, it must be capable of holding 250 lbs or more without collapsing.
Open the machine door by moving the sliding lock lever (Right side of machine) all the way up. (Close the door by reversing this process.) (You may have to slightly lift the door up or down in order to lock the lever all the way in the down position) –
You will find that the coin change/service lamp that is normally attached to the top of the machine may have been removed and placed inside the machines coin hopper for shipping purposes. It attaches to the top of the machine with the 2 machine screws that are threaded into the candle. –
You will need to open the door on the machine and remove the top glass in order to gain access to the under side where the candle mounts.
You will find a white colored quick connect plug in the area behind the top glass that the lamp will plug into.
Your jackpot reset key has been placed into the reset switch lock located on the left side of the machine.
You will only use the reset key to reset the machines jackpot alarm when someone gets lucky enough to get a jackpot or when changing games. (Otherwise you will not need to turn this key)
You should notice that we left a coin in the coin comparator which is located in the door of the machine. This coin must remain in place or your machine will not accept coins and you will get a tilt error code or the coin will jam. You will also find the power cord inside the hopper.
Route the power cord thru a small opening in the back/bottom right side and plugs into a standard 110 volt outlet. The power switch is just inside the door opening (Right side) –
There’s also a small white test switch located on the main board. You don’t need to touch that. Initially when the machine is powered on it will initialize testing memory a self test and the reels will spin up. Anytime the door is opened and closed it may or may not do the same reel spin test.
If you ever get a general reel tilt open door turn your rest key that located on the right side above your pull handle then close your door.
Try to keep the hopper full of coins at all times if you game has a hopper. If you cash the machine out and run out of coins before you run the credit counter down you will get a hopper empty error on the display which is cleared by adding quarters to the hopper and closing the door again.
The only maintenance you should experience are normal wear things like replacing burned out light bulbs and the occasional coin jam which is corrected by removing the jammed coin(s) in the coin comparator.
Another common problem is the Bill Vallidator cash box is not inserted all the way or is mis-aligned which will cause your Bill Vallidator NOT to function. Be sure it is inserted squarely and pushed all the way in place.
The tilt codes that you will run into are reset and cleared by opening and closing the machine door.
Have fun with your slot machine and if you should have any questions or concerns, please contact us so we can help.
Once again, we thank you for choosing us to make your purchase. –
Should you have any questions regarding the setup of your machine, please give us a call and we will do our best to help you out over the telephone.
95% of all problems can be resolved over the phone.
The remaining problems could be caused by the machine being banged around while in transit and might require a replacement part be sent to you. This is very rare but it can and does happen. Don’t panic! This is a casino slot machine and is very reliable.
Thank you for your Business!
Of course gambling is not a good habbit but cheating is the worst! But in history, many people have figured out a good couple of ways how to cheat slots. Below you will find 10 of them. Be aware, none of these methods will work online gaming sites like Slots Heaven!
10 – Cheat Code
Ronald Dale Harris was a talented software engineer who was working for the Nevada Gaming Commission. His job was to programming computer chips for slot machines. Since he was the programmer, he did left a cheat code like a signature of him. The code was activated by a specific combination of coins something like ‘’5 coins, wait, 2 coin, wait, 6 coins, etc.’’ and the machine would automatically pay out. Brilliant!
09 – Light Wand
Golden Nugget
Back in the day, when slot machines started using the optical sensor technology, Tommy Glenn Carmichael invented a light wand that could blind these small, magical sensors. It was something like battery-powered mini light attached to a wire.
Igt Slot Machine Troubleshooting
08 – Fake Coins
Igt Slot Machines For Sale
As simple as counterfeiting. Using advanced machinery, cheaters pressed counterfeit slot machine coins out of hardened metal dies.07 – Software Glitch
Las Vegas
Sometimes the cheat comes with the slot machine built in. The most known slot machine with its glitch was ‘’The Game King’’. To exploit the glitch, the gambler would put more money into the machine after the “double up” prompt and then switch back to the original game they were playing for $1.00. Then player would then up their stakes to the highest allotted amount and cash out.
06 –Top-bottom Joint
The top-bottom joint was a trick created by Tommy Carmichael and Ray Ming. The duo created a slider, which was made of a guitar wire and a piece of spring steel. They would snake the payout chute using the top-bottom joint until tripping the switch. Once the switch was tripped, the slot machine would empty out its payload.
05 – Computer Chip Replacement
Computer Chips
Igt Slot Machines How To Clear Codes Without
Dennis Nikrasch bought a computerized slot machine and played with it in his garage till he found a method to manipulate the computer chip inside to give him a jackpot whenever he wanted. For this purpose, he ordered the standard chips from a real manufacturer. Then he team up to obtain keys on the black market that opened slot machines. After that he would be able to open the machine to replace the chip under three minutes!
04 – Shaved Coins
As slot machine technology advanced, machine manufacturers changed optic verification sensors to prevent scams. Improved mechanisms use a beam of light to register payment as the coin dropped in. Ironically, this innovation was used against itself to perform a cheat. Shaved coins are registered by the machine but once it gets to its comparitor new mechanism which is the piece of equipment that measures the size and weight of the coin, it will be immediately kicked out because of the coins minute size discrepancy. Of course then you can use it again…
Igt Slot Machines Programming Codes
03 – Piano Wire
Piano wires
Igt Slot Machine Repair
This method dates back to 1982. At the Caesars Boardwalk Regency in Atlantic City, a group of cheaters surrounded a slot machine. Each of them had a job. One of the cheaters dubbed the mechanic, pried open the front and inserted 20-inch piano wires into the slot machine’s whirring guts. The group used the piano wires to jam the clock that timed each wheel’s rotation. With the help of this method, he was able to manipulate and spin the wheels till he wins.02 – Monkey Paw
The monkey’s paw was one of the early devices used by slot cheats. The mechanism was essentially a guitar or piano string attached to a bent metal rod. Cheater would jam it into the machine through an air vent and fish around for the switch that released the coin hopper.
01 – YO-YO
Chips
The cheater ties a thin cord around a coin and then places it in the slot until it registers a payment. Then yank out the coin and do the whole process over and over again. That simple!